448rwhp 2nd Gen RX7

wrx/240sx · 04-01-2006, 05:08 PM

448 hp @ rear wheels on 91 octane!!

I have a video of it on the dyno and a pile of pictures.

Here's the mod list:

*Fully built race ported motor (approx. 4,000 miles on rebuild)*

Microtech lt-8 engine management system
Microtech dash unit
Microtech handheld controller with laptop adaptor
HKS stainless steel exhaust manifold(made for 3rd gens only) custom modified by carlos gonzalez of G&S racing to fit fc3s

Turbonetics T-70 with tuff turbo option and .86 backside Q-trim
720cc primaries / 1680cc seccondaries
Custom downpipe
Racing beat 3 in exhaust
ACT 6 puck unsprung clutch with Centerforce extreme pressure plate
Greddy profec b spec 2 boost controller
Greddy turbo timer
17x8 OZ monte carlos with Nitto drag radials and Falken ziex up front
CP racing 4 point roll cage
7mm race bearings
3rd gen corner seal springs
Solid corner seals
2 piece apex seals
S4 rotors
Stainless steel fuel lines
Stainless steel oil lines
New oil cooler
AN oil feed/ drain lines for turbo
Greddy 32 row vsp-l core front mount intercooler
Greddy type-r blowoff valve
Walbro 255lph fuel pump
Battery relocation setup
Water pump mod
Custom welded intake manifold
SX fuel pressure regulator
Solid diff mount(not installed)
Slotted/cross drilled rotors
Hawk pads
Solid motor mounts
Magnecor 10mm wires

It would cost a lot more to build one yourself...he's only asking $9000 (posting it for a friend...if interested I'll pass on your contact info)

wrx/240sx · 04-01-2006, 05:09 PM

Sorry for the small pic of the dyno chart...I'll get that and a link to the dyno video.

wrx/240sx · 04-03-2006, 11:30 AM

Here is a link to the video:

http://www.webpages.uidaho.edu/~jbov...ideos/dyno.wmv

**If during the download it says "Server reset" just click Ok and continue downloading, it will resume where it left off.**

wrx/240sx · 04-03-2006, 10:01 PM

Wow...317 views and not even an offer. Just wondering what the issue is...Location? it's a Rotary? Price?

Feedback would be appreciated.

sukimoto · 04-04-2006, 06:49 AM

you should be able to tell its a rotary. do you see a valve cover?

wrx/240sx · 04-04-2006, 10:57 AM

My apologies...I should have put "The fact that it is a rotary"

Price lowered to $8200....

TokyoDrifterxo7 · 04-04-2006, 05:01 PM

a lot of us dont have that kind of money. You would have better luck on the rx7 boards. www.rx7club.com

s13/350z · 04-04-2006, 05:10 PM

I woulod agree. Its a nice car (if I was looking for an rx-7 I'd be interested), but it is expensive for this board, alot of tire kicking kids here. rx-7 club is a good place to sell it and GL.

wrx/240sx · 04-04-2006, 05:25 PM

Thanks for the replies guys...

I know he has a little more room in the price, not sure how low he would go. If anyone here is interested, just PM me an offer...he might just take it.

wrx/240sx · 04-05-2006, 12:06 PM

I was just talking to him and he said he would be willing to consider trades if anyone was interested in going that route.

A few small requirements:
Car must be paid off
Must have a clean title
No project cars/Must run

Here's what he would consider a good (fair) trade:
Impreza RS 2.5T or WRX
TSi AWD Talon/Eclipse GSX
E36 M3
Audi 1.8T
300ZX TT
240SX (Must be SR20DET/KA-T)
Caddy STS
Volvo S40
Acura RL/TL

If you have something else PM me and I'll pass it forward.

04-01-2006, 05:08 PM	#1
wrx/240sx Registered User Join Date: Dec 2003 Location: az Posts: 40	448rwhp 2nd Gen RX7 - now with video 448 hp @ rear wheels on 91 octane!! I have a video of it on the dyno and a pile of pictures. Here's the mod list: Fully built race ported motor (approx. 4,000 miles on rebuild) Microtech lt-8 engine management system Microtech dash unit Microtech handheld controller with laptop adaptor HKS stainless steel exhaust manifold(made for 3rd gens only) custom modified by carlos gonzalez of G&S racing to fit fc3s Turbonetics T-70 with tuff turbo option and .86 backside Q-trim 720cc primaries / 1680cc seccondaries Custom downpipe Racing beat 3 in exhaust ACT 6 puck unsprung clutch with Centerforce extreme pressure plate Greddy profec b spec 2 boost controller Greddy turbo timer 17x8 OZ monte carlos with Nitto drag radials and Falken ziex up front CP racing 4 point roll cage 7mm race bearings 3rd gen corner seal springs Solid corner seals 2 piece apex seals S4 rotors Stainless steel fuel lines Stainless steel oil lines New oil cooler AN oil feed/ drain lines for turbo Greddy 32 row vsp-l core front mount intercooler Greddy type-r blowoff valve Walbro 255lph fuel pump Battery relocation setup Water pump mod Custom welded intake manifold SX fuel pressure regulator Solid diff mount(not installed) Slotted/cross drilled rotors Hawk pads Solid motor mounts Magnecor 10mm wires It would cost a lot more to build one yourself...he's only asking $9000 (posting it for a friend...if interested I'll pass on your contact info) Last edited by wrx/240sx; 04-03-2006 at 11:31 AM.

04-04-2006, 10:57 AM	#6
wrx/240sx Registered User Join Date: Dec 2003 Location: az Posts: 40	My apologies...I should have put "The fact that it is a rotary" Price lowered to $8200.... Last edited by wrx/240sx; 04-04-2006 at 11:02 AM.

04-05-2006, 12:06 PM	#10
wrx/240sx Registered User Join Date: Dec 2003 Location: az Posts: 40	I was just talking to him and he said he would be willing to consider trades if anyone was interested in going that route. A few small requirements: Car must be paid off Must have a clean title No project cars/Must run Here's what he would consider a good (fair) trade: Impreza RS 2.5T or WRX TSi AWD Talon/Eclipse GSX E36 M3 Audi 1.8T 300ZX TT 240SX (Must be SR20DET/KA-T) Caddy STS Volvo S40 Acura RL/TL If you have something else PM me and I'll pass it forward. Last edited by wrx/240sx; 04-05-2006 at 10:22 PM.

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

04-01-2006, 05:09 PM	#2
wrx/240sx Registered User Join Date: Dec 2003 Location: az Posts: 40	Sorry for the small pic of the dyno chart...I'll get that and a link to the dyno video.

04-03-2006, 11:30 AM	#3
wrx/240sx Registered User Join Date: Dec 2003 Location: az Posts: 40	Here is a link to the video: http://www.webpages.uidaho.edu/~jbov...ideos/dyno.wmv If during the download it says "Server reset" just click Ok and continue downloading, it will resume where it left off.

04-03-2006, 10:01 PM	#4
wrx/240sx Registered User Join Date: Dec 2003 Location: az Posts: 40	Wow...317 views and not even an offer. Just wondering what the issue is...Location? it's a Rotary? Price? Feedback would be appreciated.

04-04-2006, 06:49 AM	#5
sukimoto 1979 Datsun 280zx Join Date: Sep 2004 Location: Wayne, Michigan Posts: 137	you should be able to tell its a rotary. do you see a valve cover?

04-04-2006, 05:01 PM	#7
TokyoDrifterxo7 Tokyo7even Join Date: Nov 2003 Location: SoCal Posts: 295	a lot of us dont have that kind of money. You would have better luck on the rx7 boards. www.rx7club.com

04-04-2006, 05:10 PM	#8
s13/350z Registered User Join Date: Dec 2003 Location: Houston, Tx Posts: 377	I woulod agree. Its a nice car (if I was looking for an rx-7 I'd be interested), but it is expensive for this board, alot of tire kicking kids here. rx-7 club is a good place to sell it and GL.

04-04-2006, 05:25 PM	#9
wrx/240sx Registered User Join Date: Dec 2003 Location: az Posts: 40	Thanks for the replies guys... I know he has a little more room in the price, not sure how low he would go. If anyone here is interested, just PM me an offer...he might just take it.