 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
|
 |
 |
 |
 |
 |
 |
 |
 |
 |
|
|||||||||||
|
|||||||||||
|
|||||||||||
|
|
|||||||
This is a discussion on MyMX73 7MGTE build within the Pictures and Video Clips forums, part of the General Forum category; I havent logged in here in a long time but id like to update you guys with my build if ...
 |
|
|
Thread Tools | Rate Thread | Display Modes |
09-19-2006, 04:34 PM
|
#1 |
|
Registered User
Join Date: Sep 2004
Location: Fredericksburg VA
Posts: 14
 |
MyMX73 7MGTE build
I havent logged in here in a long time but id like to update you guys with my build if you havent already seen it. I owe some credit to Robbie and his team at Redshift ( www.redshiftdc.com ) for assiting with some things with the car and to get it actually running by finishing up the wiring.
The chassis is a 1986 toyota cressida with a 7MGTE/R154 swap. There are some links below however the video one is very choppy and only worth a edgy pic and some audio. http://drift411.com/forums/index.php...&CODE=12&CID=1 http://www.vadriven.com/forums/showt...128500&page=12 Video: http://www.youtube.com/watch?v=i2HQl-wDEWg Hope you guys enjoy. Up to date cabin and engine   Fife Last edited by idrivetoys; 09-19-2006 at 08:08 PM. |
|
|
|
09-20-2006, 12:07 AM
|
#2 |
|
Registered User
Join Date: Nov 2005
Location: ANAHEIM
Posts: 310
|
Hello very nice I have been looking at it on club4ag,good to see you got it runing. I think its gonna look classic with those centerlines,& dunp the phuck out of it.Get it done PEACE
|
|
|
|
|
10-01-2006, 12:28 PM
|
#3 |
|
Registered User
Join Date: Sep 2004
Location: Fredericksburg VA
Posts: 14
|
Finally welding in the cage today so hopefully ill have some pics of it later
fife |
|
|
|
|
10-16-2006, 06:56 PM
|
#4 |
|
Registered User
Join Date: Sep 2004
Location: Fredericksburg VA
Posts: 14
|
ive almost finished putting in my roll cage, its a 6 point autopower, i am building boxes to make it taller as its too short, the is the first box , its 1/8 steel (scca legal) welded to the flattened floor and the cage to it, i will also be adding one more piece in the cetner for additional support.
  My BRAND NEW nardi torino from Autobocs (in japan)  i am going back top the car this weekend to put the rear struts on, put in the black dashboard, finish the cage, route some vacuums, re spray the interior, and tie up a few other loose ends, but for the most part shes done. Fife |
|
|
|
|
11-19-2006, 08:58 PM
|
#5 |
|
Registered User
Join Date: Sep 2004
Location: Fredericksburg VA
Posts: 14
|
I have a updated video of the cars first clean idle and rev
http://www.youtube.com/watch?v=uI70R_iJ8H4 fife |
|
|
|
|
| Thread Tools | |
| Display Modes | Rate This Thread |
|
|
Linear Mode
