Will Sparco Torinos fit in a 240sx?

wrx/240sx · 12-25-2003, 09:08 AM

Does anyone know if Sparco Torinos would fit in a 91 240sx fastback? I hear that there are some issues with aftermarket seats. Just wanted to see if anyone could confirm/deny this.

Thanks,

Dan

12-25-2003, 06:26 PM

i don't know about those spesific seats, however most of them just need brackets made (sometimes custom).. and even the custom ones don't cost more than a couple hundred at tops..

Forge_55b · 12-27-2003, 01:06 AM

i don't know if i remember correctly but i think theres a hump on the floor of the car that the bracket would normally go onto and this causes problems with mounting a regular bracket but as it goes with just about everything you can just make a custom bracket and figure out a way to make it work

banged240_drift · 12-28-2003, 01:00 AM

acctualy there is an article in sport compact car magazine with thier project silvia about the seats
and yes there is a hump that gets in the way of normal brackets and if you can somhow getahold of some skyline r-32 seats they will fit great......
i dont relay have the time or ide tell you some of the more important things theysaid in the article but ifi can ill try to put it up

JuN GDB · 12-29-2003, 02:22 PM

they were talking about these problems in the latest scc

wrx/240sx · 12-29-2003, 07:20 PM

I read the article in SCC and that is the reason why I started this thread. I just wanted to see if anyone had experience trying to fit the Torinos in their car.

VuDuDoc · 12-31-2003, 02:13 PM

all 24ds need special brackets more or less. You are gonna have to fab them or buy them.(reason is the cat hump drvs side and the bolt to the tranny hump)

The 24d seat is a side bolt whereas the aftermarket are popular with bolting underneath.

Common mod is washers and redrill to make them fit. i believe the slider is from 120-200 per seat alone!

Side note find r32 seats cheaper, bolt up and offer good support and comfort...or s14 seats.

12-25-2003, 09:08 AM	#1
wrx/240sx Registered User Join Date: Dec 2003 Location: az Posts: 40	Will Sparco Torinos fit in a 240sx? Does anyone know if Sparco Torinos would fit in a 91 240sx fastback? I hear that there are some issues with aftermarket seats. Just wanted to see if anyone could confirm/deny this. Thanks, Dan

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

12-25-2003, 06:26 PM	#2
totoro001 Guest Posts: n/a	i don't know about those spesific seats, however most of them just need brackets made (sometimes custom).. and even the custom ones don't cost more than a couple hundred at tops..

12-27-2003, 01:06 AM	#3
Forge_55b Registered User Join Date: Nov 2003 Posts: 76	i don't know if i remember correctly but i think theres a hump on the floor of the car that the bracket would normally go onto and this causes problems with mounting a regular bracket but as it goes with just about everything you can just make a custom bracket and figure out a way to make it work

12-28-2003, 01:00 AM	#4
banged240_drift Registered User Join Date: Nov 2003 Location: dallas/ft.worth Posts: 260	acctualy there is an article in sport compact car magazine with thier project silvia about the seats and yes there is a hump that gets in the way of normal brackets and if you can somhow getahold of some skyline r-32 seats they will fit great...... i dont relay have the time or ide tell you some of the more important things theysaid in the article but ifi can ill try to put it up

12-29-2003, 02:22 PM	#5
JuN GDB Touge Special! Join Date: Dec 2003 Location: Bay Area Posts: 137	they were talking about these problems in the latest scc

12-29-2003, 07:20 PM	#6
wrx/240sx Registered User Join Date: Dec 2003 Location: az Posts: 40	I read the article in SCC and that is the reason why I started this thread. I just wanted to see if anyone had experience trying to fit the Torinos in their car.

12-31-2003, 02:13 PM	#7
VuDuDoc Monkey Works DS Join Date: Jun 2003 Location: Washington Posts: 218	all 24ds need special brackets more or less. You are gonna have to fab them or buy them.(reason is the cat hump drvs side and the bolt to the tranny hump) The 24d seat is a side bolt whereas the aftermarket are popular with bolting underneath. Common mod is washers and redrill to make them fit. i believe the slider is from 120-200 per seat alone! Side note find r32 seats cheaper, bolt up and offer good support and comfort...or s14 seats.