 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
|
 |
 |
 |
 |
 |
 |
 |
 |
 |
|
|||||||||||
|
|||||||||||
|
|||||||||||
|
|
|||||||
This is a discussion on does the tranny bolt up???? within the TECH Discussion Forum forums, part of the TECH Discussion category; if you do a sr20det conversion does your ka24de tranny bolt up or do you need an adapter plate????...
 |
|
|
Thread Tools |
Rating: 
|
Display Modes |
04-07-2004, 04:05 PM
|
#1 |
|
Newbie
Join Date: Apr 2004
Posts: 8
|
does the tranny bolt up????
if you do a sr20det conversion does your ka24de tranny bolt up or do you need an adapter plate????
|
|
|
|
04-07-2004, 04:24 PM
|
#2 |
|
Registered User
Join Date: Dec 2003
Location: Renton.
Posts: 379
|
you need to change the bellhousing to make the sr20 bolt up to the ka tranny, thats just about as hard as finding a sr20 transmission.
|
|
|
|
|
04-07-2004, 05:22 PM
|
#3 |
|
Newbie
Join Date: Apr 2004
Posts: 8
|
what about finacially is it cheaper to find that bellhousing or what about an adapter plate???
|
|
|
|
|
04-07-2004, 06:49 PM
|
#4 |
|
Junior Member
Join Date: Feb 2004
Location: japan but now in orlando.
Posts: 137
 |
there is no adapter plate and even if there was the gearing would be all fu cked up. the ka tranny is for a na motor it is better to use a tranny that is geard for a turbo motor. so to sum it all up you need an sr tranny. i have a s13 black top with tranny,harness and ecu if your inerested. $2500 plus shipping
|
|
|
|
|
04-08-2004, 05:05 PM
|
#5 |
|
Newbie
Join Date: Apr 2004
Posts: 8
|
well does the driveshaft fit into the sr tranney?
|
|
|
|
|
04-08-2004, 07:04 PM
|
#6 |
|
Junior Member
Join Date: Feb 2004
Location: japan but now in orlando.
Posts: 137
|
yes...
|
|
|
|
|
04-09-2004, 08:28 PM
|
#7 |
|
Guest
Join Date: Nov 2003
Location: Huntington Beach
Posts: 2,566
|
Yea the drive shaft is the same thing, all you need is the SR tranny.
|
|
|
|
|
09-24-2004, 10:15 AM
|
#8 |
|
DRIVER
Join Date: May 2004
Location: Los Angeles, CA
Posts: 576
 |
Sorry to dig up old thread. But has anyone done a bell housing swap? What needs to be done to make it work? I just took a KA tranny off a DOHC engine. I heard that the gear ratio is actually the same as the SR.
Any information would help. Thanks.
__________________
Hubert Young KORE 8 Films |
|
|
|
|
09-30-2004, 01:03 PM
|
#9 |
|
Registered User
Join Date: Aug 2004
Posts: 30
|
Gear ratio is very close to the SR. Not so different that you can feel the difference.
|
|
|
|
|
09-30-2004, 01:40 PM
|
#10 |
|
Opposite Lock
Join Date: Jan 2004
Location: SoCal
Posts: 1,096
|
1-4 are identical. SR's fifth is different.
|
|
|
|
|
| Thread Tools | |
| Display Modes | Rate This Thread |
|
|
Linear Mode
