need 5sp

Dori Master · 05-11-2004, 10:39 PM

any body here know what its gunna take for a aouto to 5sp. conversion for my newest 240? I figure a tranny,drive shaft,and possibly rear end.

nissanguy_24 · 05-11-2004, 11:30 PM

the rear end and drive shaft should be fine. Im fixing to do this my self so i've been reading up on it. You should just need the transmission and the hydrallics to run it. Not tomention the clutch and brake pedal to install. And everything that goes with making those run.

Dori Master · 05-12-2004, 04:09 PM

thanx pawtna,let me know how it gose. My fiscal policy is will hold be holding me back for a while,btw any one know where i can get ahold of a **CHEAP** ka24 header?

MrodDrft · 05-12-2004, 04:12 PM

Wal*Mart

Dori Master · 05-12-2004, 08:22 PM

Yahh...I mean no.

shutUPandLEARN · 05-13-2004, 12:22 PM

here's a list. It's really easy to do. Done it a couple times.

-5 speed brake pedal
-5 speed clutch pedal
-clutch fluid reserviour
-clutch fluid hard lines
-clutch soft line
-slave cylinder
-throw out bearing
-pilot bearing
-clutch set
-flywheel
-tranny (I hope you remember this one)
-5 speed harness, or make the auto one fit (easy to figure out)
-drive shaft (get complete drive shaft, both pieces, don't piece them together from seperate cars)
-shifter
-shift boot

that should be all of it.

edit: auto and 5-speed use different sive drive shafts on 240s

hachiroku-fc3s · 05-13-2004, 12:33 PM

Quote:

Originally posted by nissanguy_24
...drive shaft should be fine...

Huh?

Dori Master · 05-13-2004, 01:43 PM

hey hachi- did driftcentrel send you to spy? j/k ,Dosent the shaft have to be shortened like 1.5 in?

05-11-2004, 10:39 PM	#1
Dori Master Newbie Join Date: May 2004 Location: Arlington,TX Posts: 5	need 5sp any body here know what its gunna take for a aouto to 5sp. conversion for my newest 240? I figure a tranny,drive shaft,and possibly rear end.

05-13-2004, 12:22 PM	#6
shutUPandLEARN Newbie Join Date: May 2004 Location: California Posts: 11	here's a list. It's really easy to do. Done it a couple times. -5 speed brake pedal -5 speed clutch pedal -clutch fluid reserviour -clutch fluid hard lines -clutch soft line -slave cylinder -throw out bearing -pilot bearing -clutch set -flywheel -tranny (I hope you remember this one) -5 speed harness, or make the auto one fit (easy to figure out) -drive shaft (get complete drive shaft, both pieces, don't piece them together from seperate cars) -shifter -shift boot that should be all of it. edit: auto and 5-speed use different sive drive shafts on 240s Last edited by shutUPandLEARN; 05-13-2004 at 01:35 PM.

05-13-2004, 01:43 PM	#8
Dori Master Newbie Join Date: May 2004 Location: Arlington,TX Posts: 5	Tacaomatose/Dori Whore hey hachi- did driftcentrel send you to spy? j/k ,Dosent the shaft have to be shortened like 1.5 in?

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

05-11-2004, 11:30 PM	#2
nissanguy_24 Guest Join Date: Jan 2004 Location: bakersfield, CA Posts: 3,197	the rear end and drive shaft should be fine. Im fixing to do this my self so i've been reading up on it. You should just need the transmission and the hydrallics to run it. Not tomention the clutch and brake pedal to install. And everything that goes with making those run.

05-12-2004, 04:09 PM	#3
Dori Master Newbie Join Date: May 2004 Location: Arlington,TX Posts: 5	thanx pawtna,let me know how it gose. My fiscal policy is will hold be holding me back for a while,btw any one know where i can get ahold of a CHEAP ka24 header?

05-12-2004, 04:12 PM	#4
MrodDrft Dorifto Pic King Join Date: Jan 2004 Location: Boston, MA Posts: 1,559	Wal*Mart

05-12-2004, 08:22 PM	#5
Dori Master Newbie Join Date: May 2004 Location: Arlington,TX Posts: 5	Yahh...I mean no.