Starlet Front End Conversion for AE86

na70sh · 06-08-2004, 02:53 PM

i noticed that the starlet looks alot like the levin from the front could there be a posible front end conversion with the corrolla

soultron · 06-08-2004, 08:33 PM

i dunno, that car is alot smaller.

mranlet · 06-09-2004, 06:13 AM

It would cost some money, but I could design and make one - Of course, everything costs money...

I doubt that this is the kind of question that people on this forum would nescessarily know (although there are often some surprise eruptions of knowledge). You might be better at club 4AG or contacting a clip importer and seeing if the bolt patterns or sizes are even remotely close.

I'm sure with enough determination it would fit, and the design does look quite similar.

Sorry I couldn't come up with a difinitive answer, but I hope that this helps. If you find out anything be sure to post it up here for future reference.

-MR

Ghost of Duluth · 06-09-2004, 07:40 AM

So do you have to be looking at naked pictures of a dictionary to have an explosion of knowledge?

Anything will fit on anything. All you need is the money, time, tools and enough drunken buddies to make it work. Usually the money and time run out before the drunken friends do and the tools run out with the friends.

mranlet · 06-09-2004, 09:29 AM

...you're just chock full of clever phrases, ghost.

I think that really all you need is the Starlet headlights, some polyfoam blocks and some fiberglass and you can make it fit easily.

-MR

Ghost of Duluth · 06-09-2004, 11:08 AM

And a hammer. A really big hammer.

06-08-2004, 02:53 PM	#1
na70sh Registered User Join Date: May 2004 Location: ca Posts: 155	starlet front end conversion for ae86 i noticed that the starlet looks alot like the levin from the front could there be a posible front end conversion with the corrolla

06-09-2004, 07:40 AM	#4
Ghost of Duluth Sixgun Join Date: Nov 2003 Location: Neverland Posts: 2,280	So do you have to be looking at naked pictures of a dictionary to have an explosion of knowledge? Anything will fit on anything. All you need is the money, time, tools and enough drunken buddies to make it work. Usually the money and time run out before the drunken friends do and the tools run out with the friends. __________________ Team SIXGUN, Don't whine about the food chain, be the top of it. Tokyo Pimps, Godzilla is coming. Lorin, oh Lorin, where have you gone?? If you're in the stands warming the bench, don't whine about the guys in the drivers seats.

06-09-2004, 11:08 AM	#6
Ghost of Duluth Sixgun Join Date: Nov 2003 Location: Neverland Posts: 2,280	And a hammer. A really big hammer. __________________ Team SIXGUN, Don't whine about the food chain, be the top of it. Tokyo Pimps, Godzilla is coming. Lorin, oh Lorin, where have you gone?? If you're in the stands warming the bench, don't whine about the guys in the drivers seats.

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

06-08-2004, 08:33 PM	#2
soultron Registered User Join Date: Dec 2003 Location: The Willy NC. Posts: 1,059	i dunno, that car is alot smaller.

06-09-2004, 06:13 AM	#3
mranlet Smokes Dynamite Join Date: Dec 2003 Location: Tampa, CT, all over the place! Posts: 1,090	It would cost some money, but I could design and make one - Of course, everything costs money... I doubt that this is the kind of question that people on this forum would nescessarily know (although there are often some surprise eruptions of knowledge). You might be better at club 4AG or contacting a clip importer and seeing if the bolt patterns or sizes are even remotely close. I'm sure with enough determination it would fit, and the design does look quite similar. Sorry I couldn't come up with a difinitive answer, but I hope that this helps. If you find out anything be sure to post it up here for future reference. -MR

06-09-2004, 09:29 AM	#5
mranlet Smokes Dynamite Join Date: Dec 2003 Location: Tampa, CT, all over the place! Posts: 1,090	...you're just chock full of clever phrases, ghost. I think that really all you need is the Starlet headlights, some polyfoam blocks and some fiberglass and you can make it fit easily. -MR